Текст то простой...
Диагностика подушек безопасности
Микра с 06/2000-
• Switch ignition ON.
• Check warning lamp illuminates for 7 seconds. Switch ignition OFF within 1 second.
• Wait 3 seconds.
• Repeat operation three times.
• Switch ignition ON.
• Ensure warning lamp flashes.
• Count SRS warning lamp flashes. Note trouble codes.
• Compare with trouble code table.
• Each trouble code consists of two groups of flashes.
• Group one consists of one or two flashes Fig, 1 [A].
• Front airbags - one 3 second flash.
• Side airbags - two 1,5 second flashes.
• Group two consists of two or more 0,5 second flashes Fig, 1 [D].
• A 0,5 second pause separates each flash Fig, 1 .
• A 2 second pause separates each group Fig. 1 [C].
• Trouble code is repeated after a 2 second pause Fig, 1 [E].
• For example: Trouble code 22 displayed Fig. 1 .
• Switch ignition OFF.
• Disconnect both battery leads.
• Wait 10 minutes. Rectify faults as necessary.
WARNING: Disconnecting the battery may erase memory from electronic units (e.g. radio).
• After system repairs reconnect both battery leads.
• Open driver's door.
• Switch ignition ON.
• Check warning lamp illuminates for 7 seconds. Wait 2 seconds.
• Check warning lamp flashes repeatedly 3 seconds ON, 2 seconds OFF.
• System repairs complete. No fault found.
• Switch ignition OFF.
NOTE: Switching ignition OFF erases trouble codes.
• If SRS warning lamp does not flash repeatedly:
• Count SRS warning lamp flashes. Note trouble codes.
• Compare with trouble code table.
• To switch OFF warning lamp diagnosis operation while fault is being detected, carry out the following procedure:
• Ensure ignition switched OFF.
• Switch ignition ON.
• Check warning lamp illuminates for 7 seconds. Switch ignition OFF within 1 second.
• Wait 3 seconds.
• Repeat operation three times.
• Switch ignition ON.
Микра до -05/2000
NOTE: Pyrotechnic pretensioners can only be checked using diagnostic equipment.
• Ensure ignition switched OFF.
• Open driver's door.
• Switch ignition ON.
• Check SRS warning lamp illuminates.
• Operate driver's door switch 5 times within 7 seconds of switching ignition ON.
• After warning lamp extinguishes, wait two seconds.
• Ensure warning lamp flashes.
• Count SRS warning lamp flashes. Note trouble codes.
• Compare with trouble code table.
• Each trouble code consists of two groups of flashes.
• Group one consists of one or two flashes Fig, 1 [A].
• Front airbags - one 3 second flash.
• Side airbags - two 1,5 second flashes.
• Group two consists of two or more 0,5 second flashes Fig. 1 [D].
• A 0,5 second pause separates each flash Fig, 1 .
• A 2 second pause separates each group Fig. 1 [C].
• Trouble code is repeated after a 2 second pause Fig, 1 [E].
• For example: Trouble code 22 displayed Fig. 1 .
• Switch ignition OFF.
• Disconnect both battery leads.
• Wait 10 minutes. Rectify faults as necessary.
WARNING: Disconnecting the battery may erase memory from electronic units (e.g. radio).
• After system repairs reconnect both battery leads.
• Open driver's door.
• Switch ignition ON.
• Check warning lamp illuminates for 7 seconds. Wait 2 seconds.
• Check warning lamp flashes repeatedly 3 seconds ON, 2 seconds OFF.
• System repairs complete. No fault found.
• Switch ignition OFF.
NOTE: Switching ignition OFF erases trouble codes.
• If SRS warning lamp does not flash repeatedly:
• Count SRS warning lamp flashes. Note trouble codes.
• Compare with trouble code table. -
• To switch OFF warning lamp diagnosis operation while fault is being detected, carry out the following procedure:
• Ensure ignition switched OFF.
• Open driver's door.
• Switch ignition ON.
• Check SRS warning lamp illuminates.
• Operate driver's door switch 5 times within 7 seconds of switching ignition ON.
• More detailed fault diagnosis information can be obtained using diagnostic equipment connected to the data link connector (DLC).